Capacitors Explained

The basics of capacitors explained

1
449

Capacitors Explained. Learn how capacitors work, where we use them and why they are important.

Scroll to the bottom to watch the YouTube tutorial.

Remember electricity is dangerous and can be fatal you should be qualified and competent to carry out electrical work. Do not touch the terminals of a capacitor as it can cause electric shock.

What is a capacitor?

Capacitor and battery
Capacitor and battery

A capacitor stores electric charge. It’s a little bit like a battery except it stores energy in a different way. It can’t store as much energy, although it can charge and release its energy much faster. This is very useful and that’s why you’ll find capacitors used in almost every circuit board.

How does a capacitor work?

I want you to first think of a water pipe with water flowing through it. The water will continue to flow until we shut the valve. Then, no water can flow.

If, after the valve we let the water flow into a tank, then the tank will store some of the water but we continue to get water flowing out of the pipe. When we close the valve, water will stop pouring into the tank but we will still get a steady supply of water out until the tank empties. Once the tank is filled again, we can open and close the valve and as long as we do not completely empty the tank, we get an uninterrupted supply of water out the end of the pipe. So we can use a water tank to store water and smooth out interruptions to the supply.

In electrical circuits, the capacitor acts as the water tank and stores energy. It can release this to smooth out interruptions to the supply.

If we turned a simple circuit on an off very fast without a capacitor, then the light will flash. But if we connect a capacitor into the circuit, then the light will remain on during the interruptions, at least for a short duration, because the capacitor is now discharging and powering the circuit.

Inside a basic capacitor we have two conductive metal plates which are typically made from aluminium or aluminium as the Americans call it. These will be separated by a Dielectric insulating material such as ceramic. Dielectric means the material will polarise when in contact with an electric field. We’ll see what that means shortly.

Inside a capacitor
Inside a capacitor

One side of the capacitor is connected to the positive side of the circuit and the other side is connected to the negative. On the side of the capacitor you can see a stripe and symbol to indicate which side in the negative, additionally the negative leg will be shorter.

If we connect a capacitor to a battery. The voltage will push the electrons from the negative terminal over to the capacitor. The electrons will build up on one plate of the capacitor while the other plate will in turn release some electrons. The electrons can’t pass through the capacitor though because of the insulating material. Eventually the capacitor is the same voltage as the battery and no more electrons will flow.

There is now a build up of electrons on one side, this means we have stored energy and we can release it when needed. Because there are more electrons on one side compared to the other, and electrons are negatively charged, this means we have one side which is negative and one side which is positive, so there is a difference in potential or a voltage difference between the two. We can measure this with a multimeter.

What is voltage?
What is voltage?

Voltage is like pressure, when we measure voltage we’re measuring the difference or potential difference between two points. If you imagine a pressurised water pipe, we can see the pressure using a pressure gauge. The pressure gauge is comparing two different points also, the pressure inside the pipe compared to the atmospheric pressure outside the pipe. When the tank is empty the gauge reads zero because the pressure inside the tank is equal to the pressure outside the tank so the gauge has nothing to compare against. Both are the same pressure. The same with voltage, we’re comparing the difference between two points. If we measure across a 1.5V battery then we read a difference of 1.5V between each end, but if we measure the same end we read zero because there’s no difference, it’s the same.

Want to learn electricity basics? CLICK HERE

Coming back to the capacitor, we measure across and read a voltage difference between the two because of the build up of electrons. We still get this reading even when we disconnect the battery.

If you remember with magnets, opposites attract and pull towards each other. The same occurs with the build up of negatively charged electrons, they are attracted to the positively charged particles of the atoms on the opposite plate, but they can’t ever reach them because of the insulating material. This pull between the two sides is an electric field which holds the electrons in place until another path is made.

Capacitor basics explained
Capacitor basics explained

If we then place a small lamp into the circuit, a path now exists for the electrons to flow and reach the opposite side. So the electrons will flow through the lamp, powering it and the electrons will reach the other side of the capacitor. This will only last a short duration though until the build up of electrons equalises on each side. Then the voltage is zero, so there is no pushing force and no electrons flow.
Once we connect the battery again, the capacitor will begin to charge. This allows us to interrupt the power supply and the capacitor will provide power during these interruptions.

Examples

We use capacitors everywhere. They look a little different but they’re easy to spot. In circuit boards they tend to look something like this and we can see them represented in engineering drawings like this. We can also get larger capacitors which are used for example on induction motors, ceiling fans or air conditioning units and we can even get enormous ones like this which are used to correct poor power factor in large buildings.

Example of Capacitor symbols
Example of capacitor symbols

On the side of a capacitor we will find two values. These will be the capacitance and the voltage. We measure the capacitance of the capacitor in the unit of Farads which we show with a capital F, although we will usually measure a capacitor in microfarads so we have a micro symbol just before this which looks something like the letter U with a tail.

Example of Capacitance
Example of Capacitance

The other value is our voltage which we measure in volts with a capital V, on the capacitor the voltage value is the maximum voltage the capacitor can handle.

This capacitor is rated at a certain voltage and if I exceed this value then it will explode.

Example of capacitor voltage
Example of capacitor voltage

Most capacitors have a positive and negative terminal. We need to make sure that the capacitor is connected correctly into the circuit.

Example of capacitor circuit board
Example of capacitor circuit board

Why we use them

One of the most common applications of capacitors in large buildings is for power factor correction. When too many inductive loads are placed into a circuit, the current and voltage waveforms will fall out of sync with each other and the current will lag behind the voltage. We then use capacitor banks to counteract this and bring the two back into alignment.

Another common application is to smooth out peaks when converting AC to DC.
When we use a full bridge rectifier the AC sine wave is flipped to make the negative cycle flow in a positive direction, this will trick the circuit into thinking it’s getting direct current.

via GIPHY

But, one of the problems with this method is the gaps between the peaks. So we use a capacitor to release energy into the circuit during these interruptions and that will smooth the power supply out to look more like DC.

How to measure capacitance with a multi meter

We can measure the capacitance and stored voltage using a multimeter. Not all multimeters have the capacitance function.

You should be very careful with capacitors as they store energy and can hold high voltage values for a long time even when disconnected from a circuit. To check the voltage, we switch to DC voltage on our meter and then connect the red wire to the positive side of the capacitor and the black wire to the negative side. If we get a reading of several volts or more then we should discharge that by safely connecting the terminals to a resistor and continue to read the voltage. We want to make sure it reduced down into the millivolts range before handling it else we can get a shock.

To measure the capacitance, we simply switch the meter to the capacitor function. We connect the red wire to the positive side and the black wire to the negative side. After a short delay the meter will give us a reading. We will probably get a reading close to the stated value but not exact.

For example, this one is rated at 1000 microfarads but we read around 946.

Example of 1000 microfarads reading on a capacitor
Example of 1000 microfarads reading on a capacitor

This one is rated at 33 microfarads but we measure around 36.

Example of capacitor
Example of capacitor

1 COMMENT

LEAVE A REPLY

Please enter your comment!
Please enter your name here